TR-825 BELT PACK RTS A5F HEADSET JACK F1 BAND
$1,866.91
Telex TR-825 UHF Two-Channel Binaural Wireless Beltpack – Beltpack
Description
Telex TR-825 UHF Two-Channel Binaural Wireless Beltpack – BeltpackOn/Off & Volume Control
Turns the beltpack power on and controls head set volume.
Wireless Talk Around (WTA)
When pressed, the user’s audio is disconnected from the wired intercom, auxiliary input/output and the base station’s local headset. Other beltpack users, on that audio channel, can hear the user as normal.
Stage Announce (SA)
When pressed, the user’s audio is routed to the stage announce connector on the back of the base station. The user also loses their sidetone as an indication that stage announce is activated. The other wireless beltpacks and wired users do not hear the user’s audio. The button is non-latching and activates the nearby red LED.
Audio Channel Select Button
Allows user to select either audio channel A or B.
Bat/Overmod Light (BAT/OM)
Light will flash once when unit is turned on if the battery is good. If the light stays on, battery is low. If the light does not flash, battery is dead. A normal microphone gain setting will cause the LED to flash at the beginning of most words at normal speech levels. If the gain is too high, the LED will be red during the complete word at normal speech levels.
Talk Light
LED is on when the talk button, SA or WTA is active.
Talk Button
Press to enable the audio path from the local headset microphone. The “TALK” LED, #6, will turn red when enabled. A quick press and release latches the talk function, unless latching has been disabled. Holding the button for over ½ a second will cause the audio path to be enabled only for as long as the button is held. If the talk function is latched on, pressing the talk button again will turn it off.
Additional information
| Product Type | Intercom Sub Station |
|---|---|
| Product Name | TR-825 UHF Two-Channel Binaural Wireless Beltpack |
| Width | 3.8" |
| Height | 5.4" |
| Weight (Approximate) | 1.31 lb |
| Certifications & Standards | FCC |
| Compatibility | Telex RadioCom BTR-800 Two-Channel UHF Synthesized Wireless Intercom Base Station |
| Package Contents | TR-825 UHF Two-Channel Binaural Wireless BeltpackAntenna |
| Additional Information | Current Draw: 190 mA Push-to-Talk, A and B Talk OnDistortion: < 1 % at full deviationFrequency Response: 300 Hz-8 kHzFunction: User StationIF Selectivity: 3 dB at 230 kHzImage Rejection: 70 dB or betterLocal Headset Output: 40 mW output into 600W 1% distortionMicrophone Input Sensitivity: 7 mVRF Frequency Range: 470 – 608 MHz, 614 – 740 MHz in 18 MHz TX and RX bandsRF Frequency Stability: 0.01 %RF Sensitivity: < 0.7 µV for 12 dB SINADSquelch Quieting: 90 dBSquelch Threshold: 20 dB SINAD About 1.0 µVType: Dual Conversion Super heterodyne, Synthesized, FM, 712 channelsA5F Headset Jack |
| Marketing Information | On/Off & Volume Control Turns the beltpack power on and controls head set volume.Wireless Talk Around (WTA) When pressed, the user's audio is disconnected from the wired intercom, auxiliary input/output and the base station's local headset. Other beltpack users, on that audio channel, can hear the user as normal.Stage Announce (SA) When pressed, the user's audio is routed to the stage announce connector on the back of the base station. The user also loses their sidetone as an indication that stage announce is activated. The other wireless beltpacks and wired users do not hear the user's audio. The button is non-latching and activates the nearby red LED.Audio Channel Select Button Allows user to select either audio channel A or B.Bat/Overmod Light (BAT/OM) Light will flash once when unit is turned on if the battery is good. If the light stays on, battery is low. If the light does not flash, battery is dead. A normal microphone gain setting will cause the LED to flash at the beginning of most words at normal speech levels. If the gain is too high, the LED will be red during the complete word at normal speech levels.Talk Light LED is on when the talk button, SA or WTA is active.Talk Button Press to enable the audio path from the local headset microphone. The "TALK" LED, #6, will turn red when enabled. A quick press and release latches the talk function, unless latching has been disabled. Holding the button for over ½ a second will cause the audio path to be enabled only for as long as the button is held. If the talk function is latched on, pressing the talk button again will turn it off. |
| Product Line | RadioCom |
| Product Model | TR-825 |
| Number of Channels | 2 |
| Manufacturer | The Bosch Group |
| Manufacturer Website Address | |
| Manufacturer Part Number | TR-825-F1R5 |
| Number of Batteries Supported | 6 |
| Battery Size Supported | AA |
| Product Color | Black |
| Product Family | RadioCom |
| Brand Name | Telex |
| Form Factor | Beltpack |
| Power Source | Battery |
| Depth | 2" |
